Opel Vectra B

since 1995 release

Repair and operation of the car



Vektr's Opel of B
+ 1.1. Governing bodies and control devices
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
- 9. Running gear
   9.1. Introduction
   9.2. Technical characteristics
   9.3. Rotary fists
   9.4. Replacement of forward hug bearings
   9.5. Forward lower frame
   9.6. The lobby is resistant
   9.7. Stabilizer of cross stability of a forward suspension bracket
   9.8. Lower lever of a forward suspension bracket
   9.9. Replacement of the lower hinge of a forward suspension bracket
   9.10. Back nave
   9.11. Back rack
   9.12. Stabilizer of cross stability of a back suspension bracket
   9.13. Top lever of a back suspension bracket
   9.14. Lower lever of a back suspension bracket
   9.15. Steering wheel
   9.16. Steering column
   9.17. Intermediate shaft of a steering column
   9.18. Replacement of protective covers of steering transfer
   9.19. Steering transfer
   + 9.20. Pump of the amplifier of steering
   9.21. Removal of air from system of steering with the amplifier
   9.22. Tip of steering draft
   9.23. Steering draft
   9.24. Angles of installation of wheels
+ 10. Body
+ 11. Electric equipment
+ 12. Main malfunctions


d65d3f49

9.15. Steering wheel

MODELS WITHOUT SAFETY CUSHION

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Establish forward wheels for the movement directly forward.
3. Remove the button of a sound signal from a steering wheel and disconnect the electric socket.
4. The screw-driver unbend a short mustache of fixing of a nut of fastening of a steering wheel
5. Unscrew a nut of fastening of a steering wheel.
6. Put tags of combination of a steering wheel and a steering shaft.
7. Using a stripper, remove a steering wheel and a spring from a steering shaft.
8. Establish a spring and a steering wheel on vents of a steering shaft. At the same time combine the tags made at removal of a steering wheel.
9. Establish a new spring washer and screw a nut of fastening of a steering wheel, having tightened it the required moment.
10. The screw-driver unbend a short mustache of fixing of a nut of fastening of a steering wheel.
11. Connect the electric socket to the button of a sound signal and install the button in the center of a steering wheel.
12. Connect the accumulator and check action of a sound signal.

MODELS WITH THE SAFETY CUSHION

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
Prevention

You make further actions not earlier than in 1 minute that the condenser of the airbag was discharged completely.


2. Establish forward wheels for the movement directly forward.
3. Unscrew two screws from a back part of a steering wheel.
4. Being careful, remove the safety airbag.
5. Disconnect the electric socket from a safety cushion.
6. In the presence disconnect the electric socket from the switch of control of the radio receiver.
7. The screw-driver unbend a short mustache of fixing of a nut of fastening of a steering wheel. Completely unscrew bolts of fastening of a wheel and remove a wheel.
8. Unscrew and remove a nut of fastening of a steering wheel.
9. Remove a spring washer.
10. Apply combination tags on a steering wheel and a steering shaft.
11. Using a stripper, remove a steering wheel from grooves of a steering shaft.
12. At removal of a steering wheel pass an electrical wiring of control of the radio receiver through an opening of a steering shaft.
13. Establish a steering wheel on vents of a steering shaft and pass through an opening of a steering wheel of a wire of control of the radio receiver.
14. Establish a washer, screw a nut of fastening of a steering wheel, having tightened it the required moment. Record a nut from an otvorachivaniye a washer uvula bending.
15. Connect the electric socket of the switch of control of the radio receiver
16. Install the safety airbag, previously having connected the electric socket. Fix a pillow by screws.
17. Connect the accumulator.