Opel Vectra B

since 1995 release

Repair and operation of the car



Vektr's Opel of B
+ 1.1. Governing bodies and control devices
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
- 5. Fuel system
   + 5.1. Fuel system of petrol engines
   - 5.2. Fuel systems of the diesel engine
      5.2.1. Introduction
      5.2.2. Technical characteristics
      5.2.3. Air filter and air inlet channels
      5.2.4. Accelerator pedal
      5.2.5. Filling and pumping of fuel system
      5.2.6. Fuel level sensor
      5.2.7. Fuel tank
      5.2.8. Check and adjustment of the maximum turns
      5.2.9. Start of the cold engine
      + 5.2.10. Electric knots of system of injection
      5.2.11. Fuel pump of high pressure
      5.2.12. Check of the moment of injection of fuel
      5.2.13. Adjustment of the moment of injection of fuel
      5.2.14. Fuel nozzles
      5.2.15. Turbocharger
      5.2.16. Heat exchanger
      5.2.17. Inlet collector
      5.2.18. Final collector
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. Running gear
+ 10. Body
+ 11. Electric equipment
+ 12. Main malfunctions


d65d3f49

5.2.11. Fuel pump of high pressure

Removal and installation

ENGINES OF 1,7 L

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator. Remove an inlet collector.
2. Remove a pulley from the fuel pump.
3. Remove an oil filter.
4. Remove an accelerator cable from the fuel pump.
5. Press hoses of supply of cooling liquid, weaken collars and remove both hoses from the thermostatic capsule of the fuel pump (it is specified by an arrow).
6. Disconnect fuel hoses from the fuel pump and close them traffic jams.
7. Unscrew couplings and remove the fuel-supply lines connecting the fuel pump to fuel nozzles.
8. Disconnect the electric socket from the control unit of the electromagnetic valve of a stop of the engine.
9. Using a marker or a chertilka, note a vystupaniye of a forward part of the fuel pump concerning an arm.
10. Unscrew bolts of fastening (V) of a back part of the fuel pump to an arm of the block of cylinders. Unscrew nuts of fastening (A) of a forward part of the fuel pump and remove the fuel pump.
11. Install the fuel pump on the engine and, without tightening, put the clamps and bolts of fastening of the fuel pump.
12. Install the fuel pump on an arm according to earlier put tags and previously tighten nuts and bolts of fastening of the pump.
13. Establish a pulley of the fuel pump and a gear belt.
14. Adjust the moment of injection of the fuel pump.
15. Establish the fuel pipes connecting the fuel pump and fuel nozzles.
16. Connect the electric socket to the control unit of the electromagnetic valve of a stop of the engine.
17. Connect the giving and returnable fuel hoses to the fuel pump.
18. Connect hoses of supply of cooling liquid to the thermostatic capsule of the fuel pump.
19. Connect an accelerator torso to the fuel pump.
20. Establish an inlet collector.
21. Establish an oil filter and add engine oil in the engine.
22. Connect the accumulator, start the engine and check tightness of fuel system.
23. Warm up the engine up to the working temperature and if it is necessary, adjust idling turns.

ENGINES OF 2,0 L

PERFORMANCE ORDER
1. Remove an inlet collector.
2. Having unscrewed fastening bolts (are specified by shooters), disconnect the giving and returnable fuel pipes from the fuel pump of high pressure.
3. Remove the top chain and asterisks.
4. Through an opening in the lower asterisk unscrew bolts of fastening (1) of a forward part of the fuel pump.
5. Unscrew bolts (are specified by shooters) and remove a fastening arm from a back part of the fuel pump.
6. Remove the fuel pump together with a sealing ring (it is specified by an arrow).
7. Before installation check that the safety lock in a ledge of an asterisk of the fuel pump is combined with a pump housing opening, and check that the camshaft and a bent shaft are installed in the situation corresponding to the top dead point of the first cylinder in a compression step.
8. Install a new sealing ring on the fuel pump.
9. Install the fuel pump, combining the lower asterisk of a chain with a pump ledge, and fix the pump by bolts. Establish a back arm of the fuel pump and fix by bolts.
10. Establish the top chain and asterisks.
11. Screw fuel tubes on the fuel pump.
12. Establish an inlet collector.
13. Connect the accumulator, start the engine and check tightness of fuel system.