Opel Vectra B

since 1995 release

Repair and operation of the car



Vektr's Opel of B
+ 1.1. Governing bodies and control devices
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
- 5. Fuel system
   - 5.1. Fuel system of petrol engines
      5.1.1. Introduction
      5.1.2. Technical characteristics
      5.1.3. Air filter and inlet channels
      5.1.4. A control system of temperature of the air given to the engine
      5.1.5. Accelerator cable
      5.1.6. Accelerator pedal
      5.1.7. Fuel
      - 5.1.8. System of injection of fuel
         5.1.8.1. Single-point system of injection of fuel of the SOCH engine of 1,6 l
         5.1.8.2. Multipoint system of injection of Multec-S fuel of the DOCH engine of 1,6 l
         5.1.8.3. Multipoint system of injection of Simtec 56.5 fuel of engines 1,8 and 2,0 of l
      5.1.9. Removal of pressure in fuel system
      5.1.10. Fuel pump
      5.1.11. Fuel level sensor
      5.1.12. Fuel tank
      5.1.13. Throttle case
      5.1.14. Check of system of injection of fuel
      5.1.15. Elements of single-point system of injection of fuel
      + 5.1.16. Elements of multipoint system of injection of fuel
      5.1.17. Inlet collector
      5.1.18. Final collector
      5.1.19. System of production of exhaust gases
   + 5.2. Fuel systems of the diesel engine
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. Running gear
+ 10. Body
+ 11. Electric equipment
+ 12. Main malfunctions


d65d3f49

5.1.8.2. Multipoint system of injection of Multec-S fuel of the DOCH engine of 1,6 l

GENERAL INFORMATION

Multipoint system of injection of Multec fuel - S of the DOCH engine of 1,6 l

1. Sensor of provision of a bent shaft
2. Detonation sensor
3. System of repeated combustion of exhaust gases
4. Throttle potentiometer
5. Step engine of management of idling turns
6. Mardatchik
7. System of catching of vapors of fuel
8. Ignition block
9. Oxygen sensor
10. Sensor of temperature of cooling liquid
11. The sensor of temperature of the air coming to the engine
12. Camshaft sensor

The Multec system – the joint system of ignition and injection of fuel, also turns on the catalyst, a control system of release of vapors of fuel and system of repeated combustion of exhaust gases.

The fuel pump shipped in the fuel tank gives fuel from a tank to a fuel nozzle via the filter. Fuel pressure in system is run by pressure regulator. The regulator allows excess fuel to come back to the fuel tank at excess of pressure in fuel system.

The electric control system consists of the ECU block together with the following sensors:

 – the potentiometer of a butterfly valve reports to the ECU block the provision of opening or closing of a butterfly valve;
 – the sensor of temperature of cooling liquid reports to the ECU block engine temperature;
 – the sensor of temperature of the air coming to the engine reports to the ECU block temperature of the air coming to the engine;
 – the sensor of oxygen reports to the ECU block the content of oxygen in exhaust gases;
 – the sensor of provision of a bent shaft reports to the ECU block the frequency of rotation of the engine and the provision of a bent shaft;
 – the detonation sensor installed in the block of cylinders is used for detection of the beginning of a detonation or early ignition;
 – the sensor of position of the camshaft reports to the ECU block position of the camshaft;
 – the sensor of absolute pressure in a collector reports to the ECU block depression in an inlet collector;
 – the sensor of the ABS block reports to the ECU block the relative speed of the car;
 – the switch of the compressor of the air conditioning system reports to the ECU block about inclusion of air conditioning system.

All information from sensors is analyzed by the ECU block and on this basis the block defines the corresponding corner of an advancing of ignition and composition of fuel mix. The ECU block operates fuel nozzles, determining the impulse width, that is an interval of time when the nozzle is open to provide richer or poorer fuel mix. Multec-S – consecutive system of injection of fuel, that is each of four fuel nozzles opens before opening of the inlet valve.

The ECU block also controls idling turns. For this purpose there is a step engine operating the provision of a butterfly valve.

The ECU block also operates composition of exhaust gases and a control system of release of vapors of fuel.

If there is a mistake in any of the data obtained from sensors, ECU is included into a way of the doubler. In this case the ECU block ignores the wrong signal of the sensor and accepts previously programmed value which allows the engine to continue work, though with smaller efficiency. If ECU is included into a way of the doubler, then the lamp of the alarm system on a combination of devices will light up and damage will be written down in memory of ECU. After that it is necessary to carry out full test of a control system of the engine, using the special electronic diagnostic test bench which just turns on in the diagnostic socket of system. The socket is located behind the central console. At the same time for access to it it is necessary to remove decorative finishing in front of the lever of the emergency brake.