Vektr's Opel of B
+ 1.1. Governing bodies and control devices
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
- 5. Fuel system
- 5.1. Fuel system of petrol engines
5.1.1. Introduction
5.1.2. Technical characteristics
5.1.3. Air filter and inlet channels
5.1.4. A control system of temperature of the air given to the engine
5.1.5. Accelerator cable
5.1.6. Accelerator pedal
5.1.7. Fuel
+ 5.1.8. System of injection of fuel
5.1.9. Removal of pressure in fuel system
5.1.10. Fuel pump
5.1.11. Fuel level sensor
5.1.12. Fuel tank
5.1.13. Throttle case
5.1.14. Check of system of injection of fuel
5.1.15. Elements of single-point system of injection of fuel
+ 5.1.16. Elements of multipoint system of injection of fuel
5.1.17. Inlet collector
5.1.18. Final collector
5.1.19. System of production of exhaust gases
+ 5.2. Fuel systems of the diesel engine
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. Running gear
+ 10. Body
+ 11. Electric equipment
+ 12. Main malfunctions
|
FUEL NOZZLE
Fuel nozzle, it is central installed in the case of throttles is the electromagnetic valve which gives a certain dose of fuel for the corresponding mode of loading of the engine. This dose of fuel in the form of small sprayed particles goes directly to an inlet collector. At the same time the nozzle is under constant pressure of fuel which is provided with the fuel pump and is supported by pressure regulator.
Removal and installation
| PERFORMANCE ORDER |
| 1. Take off pressure in fuel system and remove a weight wire from the accumulator. |
| 2. Weaken a collar and remove an air inlet pipe from a throttle case casing. Disconnect hoses, unscrew screws and remove the top casing of the case of a throttle. |
|
|
3. Release clamps and disconnect the electric socket from a fuel nozzle. |
|
4. Unscrew the screw of fastening of the plate holding a fuel nozzle. |
| |
5. Remove a plate of fastening of a fuel nozzle. |
|
6. Take a fuel nozzle from the case of throttles together with sealing rings (are specified by shooters). |
| 7. Installation is made in the sequence, the return to removal. At the same time on a fuel nozzle it is necessary to establish new sealing rings. |
|
PRESSURE REGULATOR
Prevention
The regulator of pressure is a component of the top section of the case of throttles.
Removal and installation
| PERFORMANCE ORDER |
| 1. Take off pressure in fuel system and remove a weight wire from the accumulator. |
| 2. Weaken a collar and disconnect an air inlet pipe from the top casing of throttles. Disconnect hoses, unscrew screws and remove the top casing of the case of throttles. |
|
|
3. Using a marker, apply combination tags on a cover of the regulator and the case of throttles. Then unscrew screws (are specified by shooters) and uncover pressure regulator. |
|
4. Uncover (4), then take a nest of a spring (3), a spring (2) and a diaphragm (1). Check a condition of a diaphragm and, if necessary, replace. |
| 5. Installation is made in the sequence, the return to removal. |
|
ENGINE OF MANAGEMENT OF IDLING TURNS
Removal and installation
| PERFORMANCE ORDER |
| 1. Remove a weight wire from the accumulator. |
| 2. For improvement of access to the engine weaken a collar and disconnect an air inlet pipe from the top casing of a throttle. Disconnect hoses, unscrew screws and remove the top casing of the case of throttles. |
|
|
3. Weaken clamps and disconnect electric sockets from the step engine operating turns of idling which is established in a forward part of the case of throttles. |
|
4. Unscrew screws and remove the engine of management of idling turns (it is specified by an arrow). |
|
5. Installation is made in the sequence, the return to removal. At the same time it is necessary to establish a new sealing ring. Also check that the end face of a plunger does not come more than to 28 mm from the engine. If it is necessary, moving a plunger, establish its correct vystupaniye. |
|
THROTTLE POTENTIOMETER
Removal and installation
| PERFORMANCE ORDER |
|
|
1. Remove a weight wire from the accumulator. Weaken clamps and remove the electric socket from a potentiometer of a throttle which is established on the left side of the case of throttles. |
| |
2. Unscrew screws and remove a potentiometer. |
| 3. Before installation apply the means interfering their unscrewing on a carving of bolts, establish a potentiometer and fix by bolts, having tightened them the required moment. |
|
SENSOR OF TEMPERATURE OF COOLING LIQUID
The sensor of temperature of cooling liquid is installed in a back part of an inlet collector.
THE SENSOR OF ABSOLUTE PRESSURE IN THE INLET COLLECTOR
The sensor of absolute pressure in an inlet collector is installed on a partition of a motor compartment to the left of the case of throttles.
Removal
| PERFORMANCE ORDER |
| Switch off ignition, disconnect the electric socket and a vacuum hose from the sensor. Unscrew and remove the sensor. |
|
SENSOR OF THE BENT SHAFT
The sensor is installed on a back part of the block of cylinders and is available from below the car.
Removal and installation
| PERFORMANCE ORDER |
| 1. Lift a forward part of the car and record on supports. |
| 2. Take electric conducting of the sensor from brackets of fastening and disconnect the electric socket of the sensor. |
|
3. Unscrew a bolt (it is specified by an arrow) and remove the sensor. |
| 4. Installation is made in the sequence, the return to removal. |
| 5. Using a probe edge, check that the gap between an end face of the sensor and teeths of a pulley of a bent shaft made 1±0,7 mm. |
|
DETONATION SENSOR
The sensor of a detonation is installed on a back part of the block of cylinders and is available from below the car.
Removal and installation
| PERFORMANCE ORDER |
| 1. The sensor of a detonation is installed on a back part of the block of cylinders and is available from below the car. Lift a forward part of the car and record on supports. |
| 2. Disconnect the electric socket of the sensor located on sensor wires. |
| 3. Unscrew a bolt and remove the sensor from the engine. |
| 4. Check, the interfaced surfaces of the sensor and the block of cylinders pure and dry, install the sensor, fix by a bolt and connect the electric socket. |
|
ELECTRONIC CONTROL DEVICE (ECU)
The ECU block is located under a water reflector before a windshield.
Removal and installation
| PERFORMANCE ORDER |
| 1. Remove a weight wire from the accumulator. Remove screen wiper levers. |
| 2. Remove the top consolidation from a partition of a motor compartment and remove a water reflector. |
| 3. Unscrew nuts and remove the protection cover of the ECU block. |
| 4. Disconnect electric sockets, unscrew nuts and remove the ECU block. |
| 5. Installation is made in the sequence, the return to removal. |
|
RELAY OF THE FUEL PUMP
The relay of the fuel pump is located in a motor compartment in the relay block.
Removal and installation
| PERFORMANCE ORDER |
| 1. Uncover the block of the relay and remove the relay of the fuel pump which is painted in violet color. |
| 2. Installation is made in the sequence, the return to removal. |
|
|
|
