Opel Vectra B

since 1995 release

Repair and operation of the car



Vektr's Opel of B
+ 1.1. Governing bodies and control devices
+ 2. Maintenance
- 3. Engines
   + 3.1. Repair of the SOCH engine installed in the car
   + 3.2. Repair of the DOCH engine installed in the car
   - 3.3. Repair of the diesel engine of 1,7 l installed in the car
      3.3.1. Introduction
      3.3.2. Technical characteristics
      3.3.3. Check of pressure of compression
      3.3.4. Top Dead Point (TDP) of the piston of the first cylinder
      3.3.5. Cover of a head of the block of cylinders
      3.3.6. Pulley of a bent shaft
      3.3.7. Casings of a gear belt
      3.3.8. Replacement of a gear belt
      3.3.9. Mechanism of a tension of a gear belt and pulleys
      3.3.10. Replacement of a sealing ring of a cam-shaft
      3.3.11. Check and adjustment of gaps of valves
      3.3.12. Cam-shaft and pushers
      3.3.13. Head of the block of cylinders
      3.3.14. Oil pallet
      3.3.15. Oil pump
      3.3.16. Oil heater
      3.3.17. Flywheel
      3.3.18. Replacement of sealing rings of a bent shaft
      3.3.19. Replacement of support of the power unit
   + 3.4. Repair of the diesel engine of 2,0 l installed in the car
   + 3.5. Capital repairs of engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. Running gear
+ 10. Body
+ 11. Electric equipment
+ 12. Main malfunctions


d65d3f49

3.3.7. Casings of a gear belt

GENERAL INFORMATION

Gas distribution drive mechanism

1. Gear belt
2. Tension mechanism
3. Bolt of fastening of the mechanism of a tension
4. Tension mechanism axis
5. Bolt of fastening of the lever of the mechanism of a tension
6. Finger
7. Washer
8. Spring
9. Single pulley
10. Bolt of a single pulley
11. Camshaft pulley
12. Bolt of fastening of a pulley distributive
shaft
13. Flange of a pulley distributive
shaft
14. Screw
15. Pulley of a bent shaft
16. Pin
17. Laying
18. Pulley of the fuel pump
19. Nut
20. Pulley of the oil pump
21. Nut
22. Top casing
23. Consolidation
24. Consolidation
25. Lower casing
26. Consolidation
27. Consolidation
28. Back casing
29. Bolt
30. Bolt
31. Bolt

Removal

PERFORMANCE ORDER
Top casing
1. Lift a forward part of the car and record on supports. Remove the right forward wheel.
2. Remove a casing of the air filter.
3. Take off auxiliary driving belts.
4. On the models equipped with air conditioning unscrew a bolt of fastening of the mechanism of a tension of a driving compressor belt and remove it.
5. Establish a jack under the engine and through wooden whetstone raise the engine until all top of the engine is not perceived by a jack. Unscrew nuts and remove the right suspension bracket of the power unit.
6. Unscrew bolts and remove the top casing of a gear belt together with rubber consolidation.
Lower casing
7. Remove the top casing of a gear belt.
8. Remove a pulley of a bent shaft.
9. Unscrew bolts and remove the lower casing of a gear belt together with rubber consolidation.
Internal casing
10. Take off a gear belt.
11. Remove a camshaft pulley, a pulley of the fuel pump of high pressure, a single pulley and the mechanism of a tension.
12. Unscrew bolts and remove an internal casing of a gear belt.

Installation

PERFORMANCE ORDER
Installation is made in the sequence, the return to removal. At the same time check correctness of an arrangement of rubber laying.