Opel Vectra B

since 1995 release

Repair and operation of the car

Vektr's Opel of B
+ 1.1. Governing bodies and control devices
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. Running gear
+ 10. Body
- 11. Electric equipment
   - 11.1. Electric equipment
      11.1.1. Introduction
      11.1.2. Technical characteristics
      11.1.3. Electric chains
      11.1.4. Detection of not closed chain
      11.1.5. Safety locks and relay
      11.1.6. Switches
      11.1.7. Bulbs of external lighting
      11.1.8. Bulbs of internal lighting
      11.1.9. Devices of external lighting
      11.1.10. Adjustment of light of headlights
      11.1.11. Combination of devices
      11.1.12. Screen wiper levers
      11.1.13. Engine of a screen wiper and draft
      11.1.14. Engine of a screen wiper of a back door
      11.1.15. Windscreen washer
      11.1.16. Radio tape recorder
      11.1.17. Loudspeakers
      11.1.18. Safety cushion
      11.1.19. Safety cushion elements
   + 11.2. Electrical circuitries
+ 12. Main malfunctions

11.1.8. Bulbs of internal lighting

FORWARD ILLUMINATION OF SALON

PERFORMANCE ORDER


1. Being careful, the screw-driver remove a lamp of illumination of salon from a ceiling.
	2. Take a bulb from spring contacts.
3. Establish a new bulb in the sequence, the return to removal. Check that the bulb is accurately recorded between spring contacts. If it is necessary, previously turn in contacts.

BACK BULB OF ILLUMINATION OF SALON

PERFORMANCE ORDER

	1. Being careful and using the screw-driver, take a back bulb of illumination of salon from a ceiling. Take a bulb from spring contacts.
2. Establish a new bulb in the sequence, the return to removal. Check that the bulb is accurately recorded between spring contacts. If it is necessary, previously turn in contacts.

ILLUMINATION OF THE LUGGAGE COMPARTMENT

PERFORMANCE ORDER

	1. Being careful and using the screw-driver, remove a bulb of illumination of the luggage compartment.
	2. Take a bulb from spring contacts.
3. Establish a new bulb in the sequence, the return to removal. Check that the bulb is accurately recorded between spring contacts. If it is necessary, previously turn in contacts.

BULBS OF THE COMBINATION OF DEVICES

PERFORMANCE ORDER

1. Remove a combination of devices.

2. For removal of a bulb of an incandescence turn a cartridge of a bulb and take it from a combination of devices (in the photo at the left – removal of the little boss, on the right – big).
	3. Take a bulb from the boss, having pulled it on themselves. Pay attention that some bulbs cannot be taken from cartridges.
4. Establish a new bulb in the sequence, the return to removal.

LIGHTING SWITCH ILLUMINATION

PERFORMANCE ORDER

1. Remove the lighting switch.
	2. Using the screw-driver, turn a cartridge of a bulb and take it from a back part of the switch of lighting.
3. Establish a new bulb in the sequence, the return to removal.

BULBS OF THE MULTIPURPOSE BLOCK

PERFORMANCE ORDER

1. Remove a combination of devices.

2. Using flat-nose pliers, turn a cartridge with a bulb and take it from a back part of the multipurpose block.
3. Establish a new bulb in the sequence, the return to removal.

LIGHTING OF THE CONTROL PANEL OF THE HEATER

PERFORMANCE ORDER

1. Remove the control panel of a heater.
	2. Take the corresponding lamp, having pulled it on themselves from the holder.
3. Establish a new bulb in the sequence, the return to removal.