Vektr's Opel of B
+ 1.1. Governing bodies and control devices
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. Running gear
+ 10. Body
- 11. Electric equipment
- 11.1. Electric equipment
11.1.1. Introduction
11.1.2. Technical characteristics
11.1.3. Electric chains
11.1.4. Detection of not closed chain
11.1.5. Safety locks and relay
11.1.6. Switches
11.1.7. Bulbs of external lighting
11.1.8. Bulbs of internal lighting
11.1.9. Devices of external lighting
11.1.10. Adjustment of light of headlights
11.1.11. Combination of devices
11.1.12. Screen wiper levers
11.1.13. Engine of a screen wiper and draft
11.1.14. Engine of a screen wiper of a back door
11.1.15. Windscreen washer
11.1.16. Radio tape recorder
11.1.17. Loudspeakers
11.1.18. Safety cushion
11.1.19. Safety cushion elements
+ 11.2. Electrical circuitries
+ 12. Main malfunctions
|
Before replacement of a bulb of external lighting check the corresponding electric chain and a safety lock. Do not concern a glass flask of a lamp barehanded. The fingerprint evaporates and besieged on a reflector therefore lighting worsens. Surely replace the failed lamps with lamps of the same type. Wipe the spots arising on imprudence from touches with a pure lint-free rag or alcohol.
HEADLIGHTS
| PERFORMANCE ORDER |
|
1. Open a cowl and remove a back cover from a headlight. Pay attention that an internal headlight for passing beam, and an external headlight for driving beam. During the work on a left headlight it is necessary to remove the relay block from a forward part of the accumulator temporarily. |
|
|
| 2. Remove the electric socket from a bulb of a headlight of driving and passing beam. |
|
3. Squeeze spring brackets of fastening of a bulb and move brackets aside. |
|
4. Take a lamp from the high beam headlamp. |
|
5. Release brackets of fastening of a bulb of a headlight of passing beam. |
|
6. Remove a bulb from a headlight of passing beam. |
| 7. Establish a new bulb in the sequence, the return to removal. |
|
FORWARD DIMENSIONAL LAMP
| PERFORMANCE ORDER |
| 1. The lamp of a dimensional forward lamp is located in the high beam headlamp. Remove a back cover from a headlight. |
|
2. Take a cartridge with a bulb of a dimensional lamp from a back part of a headlight. |
| 3. Take a bulb from the boss. |
| 4. Establish a new bulb in the sequence, the return to removal. |
|
FORWARD INDEX OF TURNS
| PERFORMANCE ORDER |
| 1. Open a cowl and the screw-driver release the top bracket of fastening from outer side of a headlight. |
| 2. Take the forward index of turns from grooves in a headlight forward. |
|
3. Turn a cartridge with a bulb and take it from the forward index of turns. |
|
4. Press and turn a bulb for extraction it from the boss. |
| 5. Establish a new bulb in the sequence, the return to removal. |
|
FORWARD FOG LIGHT
| PERFORMANCE ORDER |
| 1. Uncover a back part of the fog light located in a front bumper. |
| 2. Disconnect the electric socket, weaken a bracket of fastening and take a bulb with a fog light. |
| 3. Establish a new bulb in the sequence, the return to removal. |
|
SIDE REPEATER OF TURNS
| PERFORMANCE ORDER |
|
1. Using an edge of the thin screw-driver as the lever, take the side repeater of turns from an overlay of a forward wing. |
|
2. Holding a cartridge of a bulb, turn the side repeater of turns and remove it from the boss. |
|
3. Take a bulb from the boss, having pulled it on themselves. |
| 4. Establish a new bulb in the sequence, the return to removal. |
|
BACK LAMPS
| PERFORMANCE ORDER |
| 1. Remove the finishing of the luggage compartment located opposite to back lamps. |
|
2. Press the fixing uvula in the middle of the holder of bulbs of a back lamp and take the holder of bulbs from a lamp. |
|
3. Press and turn a bulb and take it from the holder of bulbs. |
| 4. Establish a new bulb in the sequence, the return to removal. |
|
LAMP OF ILLUMINATION OF REGISTRATION PLATE
| PERFORMANCE ORDER |
| 1. Open a luggage carrier or a back door, then insert an edge of the thin screw-driver vertically between the right edge of a lamp of illumination of registration plate and a rear bumper. Weaken a clamp and take a lamp of illumination of registration plate from a bumper up. |
| 2. Press a bracket of fastening and remove a plafond from a lamp of illumination of registration plate. |
| 3. Press and turn a bulb for removal it from the boss. |
| 4. Installation of a new bulb is made in the sequence, the return to removal. |
|
TOP STOPLIGHT
| PERFORMANCE ORDER |
| 1. Open a back door and remove an upholstery of finishing of a back part of salon. |
|
2. Remove the caps closing screws. |
|
3. Unscrew screws and remove a frame together with the top stoplight. |
|
4. Separate a stoplight lamp from a frame. |
|
5. Remove a casing from the holder of bulbs |
|
6. Using the screw-driver, release clamps |
|
7. Remove a strip with glow lamps from the holder. |
|
8. Disconnect the electric socket and remove a strip with incandescence bulbs. |
| 9. Installation is made in the sequence, the return to removal. |
|
|
|
